Proposal Number L-4821 |
CNC Lathe/Turning Centre for Shaft Machining |
|
Manufacturer |
|
VDF Boehringer |
|
Model |
|
VDF 450-T4/2000 |
|
Year |
|
2012 |
|
Control |
|
Siemens 840D sl |
|
|
Swing diameter over the bed: |
|
700 mm |
|
Turning diameter: |
max. |
650 mm |
|
Workpiece length: |
max. |
2200 mm |
|
Travels: |
|
|
|
Upper Tool Turret Left: |
|
|
|
Facing travel: |
X |
340 |
|
Longitudinal travel : |
Z |
2460 mm |
|
Upper Tool Turret Right: |
|
|
|
Facing travel: |
X |
340 mm |
|
Vertical travel for off centre machining: |
Y |
+/- 100 mm |
|
Longitudinal travel: |
Z |
2460 mm |
|
Rapids: |
X/X2/Y |
15000 mm/min. |
|
|
Z/Z2/W1/W2 |
30000 mm/min. |
|
Spindle nose: |
|
DIN 55026 |
|
Spindle bore: |
|
103 mm |
|
Spindle bearing diameter: |
|
150 mm |
|
Spindle drive motor rating: |
100% / 60% |
60 / 72 KW |
|
Spindle speeds: |
|
0 - 2800 rpm |
|
Gear steps: |
|
2 |
|
Spindle torque: |
100% / 60% |
4444 / 5335 Nm |
|
C-Axis: |
C |
0.001 degrees |
|
C-Axis speeds: |
|
0 - 30 rpm |
|
C-Axis torque max.: |
40% |
600 Nm |
|
Chuck diameter: |
|
320 mm |
|
Chuck type: |
|
Roehm 320/3 |
|
Tool Turrets: |
|
2 x Sauter Disc-Type (Servo) |
|
Upper Tool Turret Left - Turret tool positions: |
|
12 |
|
Driven/Live tool positions: |
max. |
12 |
|
Tool taper: |
|
VDI 50 |
|
Driven/Live tool motor rating: |
100% |
8.17 KW |
|
Driven/Live tool speeds: |
|
rpm |
|
Drive torque: |
100% |
48 Nm. |
|
Upper Tool Turret Right - Turret tool positions: |
|
12 |
|
Driven/Live tool positions: |
max. |
12 |
|
Tool taper: |
|
VDI 50 |
|
Driven/Live tool motor rating: |
100% |
8.17 KW |
|
Driven/Live tool speeds: |
|
|
|
Drive torque: |
100% |
48 Nm. |
|
Tailstock taper: |
|
MT#5 |
|
Tailstock force: |
|
18 kN |
|
Hydraulic steady rest: |
|
|
|
Steady rest clamp range: |
|
50 - 315 mm |
|
Chip conveyor: |
|
|
|
Chip volume output: |
|
400 kg/h |
|
Discharge height: |
|
1300 mm |
|
Electrics: |
|
400-480 V / 3 Ph / 50-60 Hz. |
|
|
|
|
|
Machine weight: |
|
27000 kg |
|
Length x Width: |
|
5100 x 2800 mm |
|
Height: |
|
2860 mm |
|
Equipped with: |
|
VDF 450-T4/2000 8-Axis CNC Turning Center for Automated Production of Axles, Shafts, or similar cylindrical products.
CNC Control: Siemens Sinumerik 840Dsl Solution Line; Ethernet; Front Port USB.
Machine Features:
Twin Upper Left and Right Sauter BA-977 Disk-type Power Servo Turrets permitting highly accurate simultaneous or 1st /2nd/3rd op single setup cutting on workpieces; C-axis in main spindle;
Driven-tool capability in both upper turrets;
Y-axis in Upper Right turret;
Rohm 320/3 KKHFR Hydraulic Combination 3-Jaw Chuck featuring (counter) centrifugal-force compensation, powered face-driving center, and retractable clamping jaws at speeds below 500 rpm to permit full length roughing and finish-turning of shaft in single setup; Rohm Hydraulic turn-through steady rest Model SLZ.50315/C100- Servo-controlled and air purge for programmable positioning including interference-free locations behind main spindle and tailstock;
Servo-controlled programmable tailstock with independent cooling and pressure monitoring;
Geared High power AC Spindle motor (72 kWP @ 60% duty cycle, achieved at 130 RPM)/ produces 5335 Nm torque at spindle at 60% DC - sustainable to 130 RPM;
MINERALIT polymer concrete machine base for vibration resistance.
Equipped with:
-Rohm 320/3 Hydraulic 3-Jaw Combination Clamping and Face Driving Chuck with retractable clamping arms/jaws, and power-operated face driver. (Retract jaws to machine jaw clamping seat- part is driven by powered face driver; return jaws to clamp on part for rough turning; retract jaws again to finish turn full length end to end, driven by face driver).
-Rohm SLZ.50315/C100 Hydraulic Steady Rest 50-315 mm clamping range
- 2x (Left/Right) 12-Station Sauter Servo Power Disk Turrets (for static or driven rotary tools)
-Assortment of static tool holders
-Marposs T18 Toolsetting Probe with E32R Electrical Interface and Auto Arm
-Central lubrication unit
-Oil-Mist Filtration and Suction System
-Brinkmann/Knoll High-pressure coolant system including pumps, filtration, and reservoir
-Knoll Chip Filtration and Conveyor System
-Comprehensive documentation for machine operation, controls, programming, job setup, maintenance, assembly drawings, sub-assembly drawings & maintenance; spare parts lists, etc, in printed and electronic forms
|
|
Condition: |
|
Excellent |
|